操穴视频,日本三级网站,欧美在线看片A免费观看,无码人妻少妇久久中文字幕蜜桃

Medical

Water Electret Meltblown-Meet FFP2 & FFP3 Standard

Water-Electret-Meltblown-FFP2&FFP3-Cbt02.jpg

Compliance with EU mask standards《EN 149-2001 A1-2009》FFP2 & FFP3 levels

 

The core of the mask is the meltblown. The traditional corona thermal electret electrostatic meltblown material is made of polypropylene, adding corona when it is heated, thus formed not a permanent electrostatic electret, with little electricity charged and uneven distribution. When producing into masks, it needs stacking more polypropylene filaments to reach the qualified filtration efficiency, thus the breathing resistance will be high. Therefore, there is very few electrostatic electret meltblown on the market can meet the requirements of EU standard FFP2 and FFP3.

Hydro Charging Meltblown Manufacturing Processes 

water-electret-meltblown-SEM-cbt.jpg

Cobetter water electret meltblown, passing through a water electret equipment, firstly undergoes a cold water cooling, the pure water passes through a certain angle, pressure, and flow rate to spray the meltblown. The friction between the water and the meltblown cloth generates static electricity, which is transported through conductive material in the electret masterbatch and enters into tourmaline or zircon to achieve static retention. The advantage of water electret lies in its electrification process, which is carried out in a high humidity environment. The static electricity on the surface of the meltblown cloth is washed away by the water, leaving only the static electricity inside the meltblown.


The second process of water electret is a process of drying and electricity locking for meltblown. The drying process uses the flow of hot air, the surface temperature is increased and the surface air flow is increased to dry. This process is actually a working principle of a static elimination equipment. All of the electricity staying outside of the electret masterbatch, will be taken away. In this second process, a part of the electricity on the surface of the meltblown cloth is eliminated, that is, virtual electricity. Therefore, after the above two processes, the electret on the polypropylene can be guaranteed to be last long. 


Excellent Cobetter Water Electret Meltblown

Compared with the traditional corona thermal electret electrostatic meltblown material, Cobetter FFP2 mask meltblown / FFP3 mask meltblown is more saturated with static electricity, and its electrostatic retention is more than three times that of the electric electret, so the corresponding filtration efficiency is higher. Because the electric field is high, there are few materials to be stacked, thus the amount of polypropylene stacked is only half of the electric electret. The material required is thinner, and the breathing resistance is correspondingly lower. 


Cobetter experiments have verified that the superposition of single-layer 40g meltblown fabric and double-layer 30g meltblown fabric can effectively complete the high filtration efficiency requirements of oil particles of FFP2 and FFP3 masks of EU《EN 149-2001 A1-2009》standard. At the same time, due to low resistance of water electret meltblown itself, multi-layer superimposed will not result in resistance exceeding standard.  




Features and Advantages

  • ·   Saturated amount of static electricity

  • ·   High particle filtration efficiency

  • ·   Few Polypropylene stacking volume

  • ·   Low resistance



EU FFP2 & FFP3 Standard


PFE 
(Sodium chloride test)

 PFE

 (paraffin oil test, loading)

   Resistance 
   
(Air resistance)

   FFP 2

94 %

   240 pa

   FFP 3

99 %

   300 pa

Remarks: The European EU standard 《EN 149-2001 A1-2009》 requires both of salt particles (sodium chloride aerosol) and oil particles (paraffin aerosol, loaded till 120mg concentration environment) filtration efficiency achieve 94% and more than 99% for FFP2 and PFF3 masks. And under the condition of 95L/min wind speed, the inhalation resistance of FFP2 masks cannot exceed 240pa, and FFP3 does not exceed 300pa.



 

Links:

Cobetter water electret meltblown-meet LEVEL2 & LEVEL3 standard

Cobetter PTFE mask membrane-meet EU mask standard《EN14683:2019+AC》TYPE ⅡR level


         

BS EN 149-2001 A1-2009.pdf

BS EN 149-2001 A1-2009 picture.jpg




 


For technical data sheet or application inquiry, you are more than welcome to contact our sales representative by sales@cobetterfilter.com or leave a message






性ⅩXXXX免费大片| 久极品思思| 四虎影视.C0M| 欧美精品—色呦呦| 人妻夜夜爽天天爽欧美色院| 2019AV免费在线| 青青久久国产精品| 国产视频一区在线播放| 久久香蕉视频网站| 在线你懂的视频| 嘿嘿一区二区| 亚洲男人的天堂在线aⅴ视频| 色鬼久色| 午夜成人免费小电影| 无码av一区| 女生自慰av免费看| 国产SM主人调教女M视频| 久久伊人久久网网| 日本少妇人妻| 亚洲密乳av| 久艹精品视频| 亚洲av无码久久忘忧草| 色呦呦欧美激情| 色综合网址| 性爱一级片网站| 精品国欧很黄很黄的| 亚欧在线| 四虎影视.Tom| 国产精品美女久久久久aⅴ国产馆 亚洲片国产一区一级在线观看 | 日本激情精品二区| 成年人黄色大全| 丝袜欧美日韩一区| 亚洲高清不卡无码| 亚洲无码四虎| 国产爆操肥臀在线| 桂阳县| 性欧美性69巨大| 大胆人GOGO888体艺术摄影| 精品第六页| 国产精品一区二区在线观看99| 狠狠色精品视频免费|